GSD self-locking pneumatic lifting mast is a lifting mast specially
developed by Wenzhou Lucheng Tianhe Automation Component Factory for
long time lifting mast and ensuring that mast does not fall for a long
time.
Working principle of self-locking pneumatic lifting mast:
Plug
self-locking is based on the structural characteristics of the mast
cylinder block model, using the shear force between the guide bar of the
cylinder block and the positioning pin on the lock connection sleeve,
the mechanical positioning of each section of the mast is carried out.
Because the mast cylinder body is made of aluminium alloy and the
section area of the guide bar is very small, the plug self-locking
device is only suitable for small and medium-sized masts with light
load.
GSD self-locking pneumatic lifting mast is a lifting mast
specially developed by Wenzhou Lucheng Tianhe Automation Component
Factory for long time lifting mast and ensuring that mast does not fall
for a long time.
Characteristic
1. It can keep the lifting mast from falling for a long time.
2.
The self-locking device fittings are made of 304 stainless steel to
ensure that the structure of the self-locking device is stable and not
rusty.
3. The zipper is welded with 304 stainless steel ring to ensure that the zipper is firm and rustless.
Performance parameters of self-locking pneumatic lifting mast
Model
GSD*6-70
GSD*6-150
GSD*9-250
GSD*5-70
GSD*7-50
Initial height(m)
1.9m
3.4m
3.9m
1.95m
1.25m
Lift height（m）
7m
15m
25m
7m
5m
Node number
6
6
9
5
7
Maximum Outer Diameter of Pipe（mm）
Ø229
Ø229
Ø229
Ø160
Ø192
Vertical load（KG）
≤50kg
≤50kg
≤10kg
≤30kg
≤30kg
Working Pressure
≤0.4MPa
≤0.4MPa
≤0.4MPa
≤0.4MPa
≤0.4MPa
Wind rope
Level 2
Level 2
Level 3
nothing
nothing
Self-locking form
Cable-stayed type
Wind resistance
≤Level 8
Product Material
Industrial Special Aluminum Alloy
colour（Optional）
Bronze
Silvery white
Instructions for use of self-locking pneumatic lifting rod:
1. Before working, the air rod must be installed vertically with the working face.
2.
Reasonable loading should be carried out according to the bearing
capacity of the gas rod, and no overloading should be allowed.
3.
The power source of the rod is compressed air (40 micron) dried after
general filtration. A constant pressure relief valve of 0-2.5 kg/cm2 has
been installed between the rod and the three-point combination
(filtration, decompression, oil mist) to ensure the safe and stable lift
of the rod. Do not exceed 3kg/cm2.
4. All seals are imported. The
working temperature range is generally - 25 ~90 ~C. If special working
conditions are required, please specify separately for customization.
5.
The through-line lifting pole should pay attention to the insulation of
the cable exposed outside the pole. If there is leakage, it should be
repaired and used again.
6. Vehicle-mounted air pole can start up
and down only when the vehicle is in a static state. It is strictly
forbidden to use heavy objects to directly or indirectly impact the
cylinder block of the air pole, otherwise it will cause adverse
consequences.
7. Lifting is from top to bottom. When lifting the
first section (the smallest), the closing position lock should be opened
first and then inflated and pressurized. The air pressure should be
lowered as far as possible to prevent the equipment from being damaged
by impact.
8. When the second section is lifted, the lock pin
enters the cylinder cylinder lock hole under the action of the spring
when the first section is raised to the lifting lock position, and a
click will occur. At this time, the closed position lock of the second
section should be opened quickly.
9. When the third section is raised, repeat the second section. By analogy, until all cylinders of the lifting mast are lifted.
10.
If the lock pin is stuck because it is too late to unlock during
mid-rise, the pressure should be lowered immediately until the lock pin
can pull back, observe whether the equipment is damaged or not, and then
open the lock pin for upward operation.
11. When descending, it
descends from bottom to top. First, it opens the lift lock of the
penultimate section (the largest section), then slowly lowers the air
pressure until the lock pin enters the cylinder cylinder lock hole under
the action of the spring, and then it makes a beep. At this time, it
opens the penultimate section quickly. Lift lock,
12. In the third
penultimate section of the descent, repeat the action of the second
penultimate section, and so on, until all the lifting masts descend for
this purpose.
If the lock pin is stuck in the process of descent
due to slow action, the pressure shall be stopped immediately and the
pressure shall be slowly pressed until the lifting mast rises slightly
and the lock pin can pull back, and then the lock pin shall be opened
for descent operation.
https://www.robomasts.com/pneumatic-mast/